Impact of the amount of the gold layer on the tribological performance of the ceramic conversion treated CP-Titanium

doi:10.21203/rs.3.rs-2329080/v1

Download PDF

Research Article

Impact of the amount of the gold layer on the tribological performance of the ceramic conversion treated CP-Titanium

https://doi.org/10.21203/rs.3.rs-2329080/v1

This work is licensed under a CC BY 4.0 License

Journal Publication

published 25 Feb, 2023

Read the published version in Tribology Letters →

You are reading this latest preprint version

Titanium alloys are characterised by poor tribological properties, and a ceramic TiO2 layer formed on the surface can greatly improve its performance. By pre-depositing a gold layer on the titanium surface, the gold particles promote the outward diffusion of titanium in the ceramic conversion treatment to react with the inward-coming oxygen to form a compact titanium dioxide layer. The surface morphology, microstructure, phase constituents were characterised by SEM/EDX and XRD. The adhesion o the oxide layers were assessed by a scratch test. The distribution of gold particles in the oxide layer can enhance the surface hardness and reduce friction and wear against a WC ball in the reciprocal tribological test. The ceramic conversion process can be accelerated efficiently at 620-660°C, and the more gold pre-deposited, the thicker the oxide layer.

gold

ceramic conversion treatment

oxidation

CP-Ti

friction

wear

Due to its high strength-to-weight ratio, high biocompatibility and excellent chemical stability, commercially pure titanium (CP-Ti) is used in a wide range of industries such as the fixation of fractures and joint replacements [1]. However, titanium has a high and unstable coefficient of friction, strong adhesive tendency and high wear rate [2], thus making it difficult for high-stress and long-term applications like long-spanned fixed prostheses and the frameworks of removable partial dentures [3, 4]. Different surface engineering methods like PVD [5], CVD[6], plasma treatment [7], nitriding [8] and anodization [9] have been used to modify titanium alloys. Among them, ceramic conversion treatment (CCT) can generate a ceramic hard layer supported by a hardened diffusion zone on the surface of the titanium alloys which can greatly improve the tribological performance of titanium alloys [10]. However, the lengthy thermal-chemical process of CCT ( 50 to 100 hours at temperatures ranging from 580 to 700°C) can result in grain growth of the matrix which negatively affects its mechanical properties [3, 10, 11]. In previous research, we found that gold can promote the outward diffusion of titanium at elevated temperatures and therefore accelerate the oxidation process of CPTi and Ti6Al4V alloys[12–14]. Gold is also one of the most promising solid lubricants due to its long-term stability and frictional properties [15]. Furthermore, gold nanoparticles in the TiO₂ film can enhance its photocatalytic [16, 17] and antimicrobial activity [18] etc. Therefore, this study aimed to investigate the impact of the thickness of a pre-deposited gold layer on the CCT of CP-Ti and to clarify the role of gold in the interaction with pure titanium in oxidation. In the meantime, a variety of performance tests were used to evaluate the hardness, scratch resistance and friction and wear of the surface to study whether the addition of gold could improve the mechanical performance of CP-Ti and therefore offer an efficient surface modification of CP-Ti alloy for biomedical application.

CP-Ti bar (25.4mm in diameter) was cut into 4.5 mm thick coupons. The coupons were ground progressively from 120 grit to 1200 grit and then were cleaned in an acetone bath using an ultrasonic cleaner. After drying, gold layers of three thicknesses were pre-deposited on the cleaned CP-Ti coupons. The deposition was carried out in an Emscope SC 500 instrument under 25 mA for 3 minutes (Au3m), 6 minutes (Au6m) and 9 minutes (Au9m). Calculated based on the weight gain after deposition, the thicknesses were about 15 nm, 30 nm and 45 nm separately for Au3m, Au6m and Au8m deposition. CCT was operated in an Elite Thermal Systems Limited electric furnace with a heating rate of 8°C/min. After treatment, it was cooled down to room temperature in the furnace. At 620°C, three treatment durations (3h, 40h and 80h) were executed to compare the impact of the different amounts of gold on the CCT (Table 1). A higher temperature CCT (660°C/3h) was also used to further verify the impact of gold on the CCT of CP-Ti. The weight change after the CCT was measured via a high-precision balance OHAUS GALAXY 160D. Weight gain per unit surface area (ΔW/A) was calculated to monitor the initial impact of gold on CCT (Table 1).

Table 1

Ceramic conversion treatment detail of CP-Ti samples with different amount of pre-deposited gold layer
Sample code	Pre-deposition time (minute)	Temperature (°C)	Time (hour)	ΔW/A (µg/mm²)	Roughness (Ra, µm)
Untreated	-	-	-	-	0.158
620/3	-	620	3	1.38	0.221
Au3m620/3	3			1.97	0.257
Au6m620/3	6			3.16	0.192
Au9m620/3	9			3.35	0.165
620/40	-		40	3.94	0.120
Au3m620/40	3			5.52	0.157
Au6m620/40	6			6.51	0.276
Au9m620/40	9			8.09	0.168
620/80	-		80	6.71	0.137
Au3m620/80	3			7.50	0.108
Au6m620/80	6			8.88	0.251
Au9m620/80	9			9.66	0.185
660/3	-	660	3	1.78	0.157
Au3m660/3	3			3.16	0.201
Au6m660/3	6			4.93	0.177
Au9m660/3	9			6.11	0.131

The roughness (the arithmetic average roughness) of the surface was measured by an XP-200 Plus Stylus Profilometer (Table 1). Surface phase constituents were examined by a powder diffractometer Inel EQUINOX 3000 (2C) X-ray diffraction (XRD) using Cu-Kα radiation (λ = 0.154056 nm). It scanned from 20.01 and up to 80° with a step size of 0.02° and counting times of 2 s/step. CCTed coupons were sectioned and mounted in conductive Bakelite, ground and polished to a mirror-like finish to measure the cross-sectional hardness change. The microstructure can be revealed after etching by Kroll’s reagent of 2% HF, 10% HNO₃, and 88% H₂O. Surface morphology, cross-sectional microstructure, and elemental information were investigated by a Joel 7000 scanning electron microscope (SEM) equipped with an Oxford Inca energy dispersive X-ray spectroscopy (EDX) detector.

A Zwick Roell's Indentec hardness testing machine was used for Vickers surface micro-hardness measurement. The load was 25 gf and the holding time was 10 seconds). A Micro Materials NanoTest system was used to measure the cross-sectional nano-hardness change under a load of 20 mN with a holding time of 5 seconds. A ST30 Scratch Tester with a Rockwell spherical cone tip was used to evaluate the adhesion/cohesion strength of the converted ceramic layers. An initial load of 5 N was applied and it was increased linearly (10 mm/min) until 60 N. Friction and wear properties of the CCTed surface were tested against a tungsten carbide ball (Φ 8 mm) in a reciprocating sliding mode utilising a phoenix TE-79 multi-axis tribology machine. The temperature was between 20–22°C and the humidity was about 48–52%. A load of 20 N was used for 1000 cycles. The sliding distance was 5 mm with an average sliding speed of 5 mm/s. The geometrical shapes of the wear tracks were plotted by a profilometer, which was used to measure the depth, width and cross-sectional area of the track, and to calculate the volume of material loss. The debris and wear tracks were further analysed by SEM/EDX to study the tribological mechanism.

3.1: Surface morphology and roughness change

After the sputter deposition of the gold layer, the sample surface changed from a metallic silver appearance to golden colour, being more obvious with more gold deposited (Fig. 1 top). After CCT, all the samples lost their metallic lustre and turned into different colours indicating the change of surface morphology and roughness. After CCT at 620°C for 3 hours, the surface of CP-Ti showed some light blue colour, while all the gold pre-deposited samples turned into dark grey colour as shown in Fig. 1, and it became darker for samples with more gold pre-deposited. With increasing the treatment time to 40 and 80 hours, all the surfaces turned into deep dark grey colour, and so did the samples CCTed at 660°C for 3 hours.

The surface morphology of CP-Ti samples changed considerably after the CCT. For 620°C/3h treated samples, there were some white particles evenly dispersed on the surface for gold pre-deposited samples as seen in Fig. 2a-c. Further analyse by EDX (Fig. 3b) indicated that they were gold particles. With the increased amount of pre-deposited gold, the remaining particles on the surface became sparse and smaller (Fig. 2a to Fig. 2c). The grinding marks can still be clearly seen on the surface of sample 620/3 without any gold pre-deposition (Fig. 2d); however, they became less obvious for those samples with gold pre-deposition (Fig. 2a-c). The surface became moderately smoother with more gold pre-deposited (Table 1). Increasing the treatment time at 620°C to 40 and 80 hours, gold particles spread on the surface evenly and grew slightly bigger (Fig. 2e/f), while the roughness value increased slightly in contrast to the sample without gold (Table 1). For a higher temperature CCT (660°C for 3-hour), the same trend with larger gold particles was observed. Interestingly, with more gold pre-deposited on the surface, the gold particles became less populated and smaller for all the treatments for the same condition.

Elemental information on the surface and cross-section was collected and exemplified by the sample Au6m620/80 in Fig. 3. White particles (Spot 1 in Fig. 3b) on the surface are rich in gold, other regions are stoichiometrically TiO₂ (Spot 2 in Fig. 3b) which are similar to the spots 3/4 in Fig. 3d in the oxide layer. The inset picture in Fig. 3a demonstrates the distribution of oxygen, gold and titanium. In a fractured oxide layer (Fig. 3c), the crystalline size in Zone A near the gold line is smaller and denser than in the other zone like B. A smaller amount of gold can be detected in the oxide layer through the thickness, and tiny gold particles are evenly dispersed in the oxide layer (Fig. 3d). There is also a clear light colour mark between the oxide layer and matrix and EDX identification suggesting it has a higher content of gold (Spot 5 in Fig. 3d). Oxygen content at spot 6 in Fig. 3d is still higher indicating the oxygen diffused into the matrix during the CCT process.

3.2: Thickness of the oxide

As shown in Fig. 4 and Fig. 5, after 3-hour CCT, the thickness of the oxide layers was about 0.2–0.3 µm for CCT without any pre-deposited layer (620/3). However, the thickness of the oxide layer increased significantly with a pre-deposited gold layer, i.e., 1 µm for sample Au3m620/3. The thickness was also larger with more gold pre-deposited on the surface, 1.5 µm and 1.8 µm for samples Au6m620/3 and Au9m620/3, separately (Fig. 4a). Extending the treatment time to 40 hours and 80 hours, the oxide layer became much thicker for gold pre-deposited samples as evidenced in Fig. 4 and Fig. 5. However, for a longer treatment like 80 hours, a smaller amount of gold (Au3m620/80) only added a 0.6 µm oxide layer to 2.6 µm from 2 µm (620/80). Double the amount of gold almost doubled the oxide layer thickness, but the difference between 6-minute and 9-minute pre-deposition was not significant. Apparently, there was a gold marker between the oxide layer and the matrix after CCT. With the increasing amount of the pre-deposited gold, the marker became clearer and thicker as shown in Fig. 4a. With a similar amount of gold pre-deposited on CP-Ti samples, the thickness of the oxide layer increased with treatment time and temperature which generally followed the thermodynamic of oxidation (Fig. 4b).

3.3: Surface phase constituents

The changes in phase constituents on the surface of CPT samples after CCT are shown in Fig. 6. After 3-hour treatment at 620°C, the three α-Ti peaks (100), (002) and (101) shifted to a lower angle due to the dissolution of the oxygen atom as an interstitial element. Rutile (110) can be identified on the surface of the sample without a pre-deposited gold layer (620/3). With the pre-deposited gold layer, the rutile peaks (110), (101), (200), (111) and (210) became significant and the crystal grew bigger with the increased amount of pre-deposited gold. In the meantime, anatase (101) can also be detected on the surface of the gold pre-deposited sample. The thickness of the oxide layers increased after a longer treatment time, i.e. 620°C/80h, the intensity of the alpha peaks decreased significantly especially on the surface with a higher amount of gold (sample Au9m620/80). Although rutile phases dominated the surface, anatase can still be identified on the surface, a higher amount of gold not only promoted the oxide formation but also benefited the growth of a mixture of anatase and rutile at this temperature range. For the samples CCTed at 620°C/40h and 660°C/3h, the phase constituents had a similar trend.

3.4: Mechanical properties

3.4.1 Surface Microhardness

The surface micro-hardness of the CP-Ti samples increased remarkably after CCT (Fig. 7). After CCT at 620°C for 3 hours, the surface hardness increased from HV_0.05 274 (CPTi) to about HV_0.05 509 (620/3). All the gold pre-deposited samples had notably higher surface hardness, HV_0.05 858, HV_0.05 915 and HV_0.05 964, for Au3m620/3, Au6m620/3 and Au9m620/3 separately. The higher the amount of gold pre-deposited, the higher the surface hardness after the same CCT. A similar trend of surface hardness change occurred in other CCTs at 620°C for 40 and 80 hours and the treatment at 660°C for 3 hours as shown in Fig. 7.

3.4.2 Cross sectional nanohardness profiles

Nanoindentation was used to measure the nanohardness change under the oxide layer, and the cross-sectional nano-hardness depth profiles were plotted in Fig. 8. For CCT treatment at 620°C for 80 hours, there was a clear hardened zone up to 15 µm deep for sample 620/80; however, this zone was reduced to less than 10 µm (Fig. 8a) for those samples pre-deposited with gold. A comparable result was obtained for the sample CCTed at 620°C for 40 hours. A much shallow hardened zone of about 5 µm was found for the 3-hour short treatment at 620°C and 660°C as shown in Fig. 8b. The smaller indents near the interface in the inset pictures suggest a higher nano-hardness.

3.4.3 Scratch testing on the converted ceramic oxide layers

The scratch tests were carried out on selected samples to examine the adhesion and cohesion of the oxide layers (Fig. 9). For the short time (3-hour) treated surfaces, chips appeared at both sides from the beginning of the scratching test. Sample Au3m620/3 failed at about 20 N, and the oxide layer on sample Au9m620/3 was scrapped off at an even lower load, indicating more gold in the oxide layer led to a more brittle layer. For the longer treatment, smaller chips started to emerge at the sides for sample 620/80 when the load increased from 5 N to 10 N. The number and size of the chips both increased with the increment of the load, and a total failure occurred just under 40 N which was confirmed by the EDX analysis of the path as shown in Figs. 9b&d.

For sample Au9m620/80, larger chips appeared at the sides at a load of 10 N, and the number and size of the chips didn’t increase a lot until a load of 30 N (Fig. 9c), part of the oxide layer came off as identified by EDX (Fig. 9d). The chips developed continuously until the end of the test as indicated in Fig. 9a. A total delamination of the oxide layer occurred at a load near 40 N (Fig. 9a) which resembled that of sample 620/80.

3.4.4 Reciprocal friction and wear test against WC ball

As demonstrated in Fig. 10a, the coefficient of friction (CoF) of the untreated CP-Ti sample against the WC ball was quite high and unstable. The CoF started high at 0.50 under a load of 20 N and reduced slightly to 0.30–0.40 after a 50 cycles run-in process, it then fluctuated in the range of 0.20–0.40 before climbing again after 800 cycles to about 0.55 at the end of the test. For sample 620/3, the CoF kicked off at 0.1 and rose steadily to about 0.45 after 600 cycles, and then dropped slightly but turned more scattered. For the three samples CCTed at 620°C/3h with pre-deposited gold, the initial CoF was about 0.10, and it increased steadily to a level between 0.25 and 0.30 after 50–100 cycles and remained stable till the end of the tribo-test (Fig. 10a).

As displayed in Fig. 10b, the typical wear tracks of all the samples after tribo-test were plotted by a profilometer. Details about the thickness of the oxide layer, the width/depth of the track, the range of CoF, the wear area, and the calculated wear rate are summarised in Table 2. A deep track of 37 µm with a width of 1087 µm was produced on the untreated CP-Ti sample. The untreated sample had the highest wear rate among all the tested samples and a scuffed rough wear track with deep plastically deformed grooves and ridges was produced after the tribotest (inset picture in Fig. 10b). A lot of debris can also be found on the track which led to high and unstable friction. For sample 620/3 (Inset picture in Fig. 10a), a fractured oxide layer can be found in the whole track and some regions were delaminated. A few warped oxide layer pieces can be found in the track of sample Au3m620/3 with a much smaller number, furthermore, no total delamination of the oxide layer was found (Fig. 10a). A similar distorted oxide layer was found in the track of samples Au6m620/3 and Au9m620/3 (Inset pictures in Fig. 10c). With an increased amount of gold in the layer, the wear track was shallower and with a slower wear rate as detailed in Table 2.

As shown inFigure 11, for the sample CCTed at 620°C for 80 hours, without gold in the oxide layer, the CoF commenced at 0.12 and escalated steadily to about 0.35 after 400 cycles and then oscillated between 0.35 and 0.40, some of the oxide layers were peeled off from the surface as seen in the inset picture in Fig. 11, which might be the reason for the large fluctuations of the CoF in the second half of the tribotest. For the gold pre-deposited Au9m620/80, the onset CoF was about 0.12, it swelled to about 0.25 in the first 100 cycles and then built up smoothly to about 0.33 in the end. Some blisters can be found on the worn track and part of the oxide layers were scuffed but it was not exfoliated. The wear rate of Au9m620/80 was higher than that of 620/80. For the sample Au9m620/40, although the CoF had lower inception, it expanded rapidly to about 0.30 after 200 cycles and vibrated in the range of 0.25 and 0.35 in the remaining test. Sample Au9m660/3 had an initial CoF of 0.13, and it rose quickly in the first 200 cycles and then climbed gradually to 0.33, however, the wear track was much smoother with a very low wear rate of 3.05×10^− 6 mm³/Nm.

In this research, we found that gold can promote the oxidation of titanium, by increasing the amount of pre-deposited gold, this effect demonstrates more significantly. At the same time, the introduction of gold into the oxide layer changed the surface phase constituents and improved the mechanical properties, and therefore it is worthwhile to discuss the mechanism of the pre-deposited gold in the CCT of titanium alloys.

Table 2

Summary of the wear tracks
Sample	Thickness of oxide (µm)	CoF	Wear track width (µm)	Wear track depth (µm)	Wear area (µm²)	Wear rate (mm³/Nm)
CPTi	0	0.20–0.58	1087	37	24450	1.22E-03
620/3	0.3	0.10–0.48	243	1.26	147	7.35E-06
Au3m620/3	1	0.10–0.34	253	1.17	123	6.15E-06
Au6m620/3	1.5	0.11–0.31	256	1.06	131	6.55E-06
Au9m620/3	1.8	0.09–0.33	189	0.73	71	3.55E-06
Au9m620/40	3.5	0.08–0.33	350	2.24	500	2.50E-05
Au9m620/80	4.6	0.12–0.33	204	1.8	156	7.80E-06
620/80	2.0	0.12–0.40	186	0.76	75	3.75E-06
Au9m660/3	2.7	0.13–0.37	236	0.63	61	3.05E-06

Thanks to the high affinity of Ti for O, the oxidation of titanium alloys is dominated by the inward diffusion of O²⁻ and the outward diffusion of Ti⁴⁺[19]. In our previous study, we found that with the existence of a gold layer on the surface of the titanium alloy, the outward diffusion of Ti ions is promoted to provide more fresh titanium atoms to react with oxygen [12]. Gold has an atomic number of 79 with the electron configuration of [Xe] 4f14 5d10 6s1, and it has a multi-oxidation state. Generally, the nanosized gold particles (Fig. 1b) tend to agglomerate to large zones as shown in Fig. 12 if the gold is not compatible with a substrate like silicon. However, the gold atoms preferentially bind to titanium atoms over oxygen atoms which facilitates the formation of a strongly bonded oxygen/transition-metal system, which can enhance their reactivities [20]. O₂ can be adsorbed preferentially at the Au-TiO₂ interface and become ready to dissociate, which acts as a catalyst for the oxidation process [21]. In the initial stages, the presence of gold and its high activity dramatically increases the titanium cations’ outward diffusion through the clearance between gold particles (Fig. 1b) to meet the incoming oxygen anions and thus leads to the initial increase in the oxidation rate of titanium alloys (Fig. 13). Gold can be found at the interface of the oxide layer and within the oxide matrix for all the gold pre-deposited samples.

With more gold-pre-deposited, the oxide layer became thicker under the same treatment conditions (Fig. 4/Fig. 5). In the meantime, the gold marker line became wider and spread at the interface zone, especially for the 9-minute pre-deposited sample (Fig. 4b). The gold particles have a tendency to diffuse into the matrix of titanium (Fig. 4b) which is in agreement with other researchers’ findings [22]. This reciprocal diffusion of gold and titanium makes more fresh titanium atoms exposed at the forefront of incoming oxygen atoms/ions to form more oxides. During the growth of the oxides, a partial gold marker line was broken, and some smaller particles were left in the path of oxidation which can be seen on the surface and in the oxide layer. With increasing oxidation time, the lateral diffusion of the gold is responsible for the large gold particles on the surface as evidenced in Fig. 2a, e and f. However, the gold particles on the surface became smaller and sparse for a thick pre-deposited gold layer (Fig. 2a, b and c) which might be because a thicker oxide layer disperses the particles more. As reported by Busiakiewicz, a thin gold film formed into gold nanoparticles on rutile titanium dioxide after heat treatment at temperatures of 600°C[23]. With the increased thickness of the oxide layer, the outward diffusion of the titanium atoms through the oxide layer became difficult, and the inward diffusion of oxygen atoms/ molecules through the oxide layer to react with the titanium at the interface to form the oxide-dominated the process, leading to a slower oxidation rate.

As seen in Fig. 6, apart from rutile, some anatase phases appeared on the surface of gold pre-deposited samples which turned clearer with the increasing amount of gold pre-deposited. This is in contrast with another report that rutile is predominately formed on the surface of Ti and its alloys when oxidising at 600-700°C [24]. However, as rutile TiO₂ is a non-stoichiometric compound represented by TiO_2-x and oxygen vacancies are the main defects, doping elements with a higher valence can prevent rutile TiO₂ from forming [25]. Debeila et.al. found that gold particles were mostly on the surface of TiO₂ as metallic gold and no evidence of the substitution of Ti⁴⁺ ions by gold ions in TiO₂, which favoured in creation of oxygen vacancies and thus promote the transition of anatase to rutile [26].

Metal and bio-ceramic contact is one of the key considerations of joint replacement, therefore a ceramic WC ball was used as a counterpart ball to test the tribological properties of the titanium alloys samples in a reciprocal mode. A much wider and deeper scuffed track was produced on the untreated CP-Ti sample with the highest wear rate, and the plastically deformed grooves and ridges led to unstable friction (Fig. 10a/b and Table 2). This is probably a result of the formation and periodic localised fracture of a transfer layer [27].

The tough and adherent titanium dioxide layer with enough thickness on the surface of sample 620/80 resulted in a steady CoF and shallow wear track. This is because the oxide layer greatly reduced the adhesive action of metal/ceramic contact (Ti/WC) as a consequence of the nature of the ceramic/ceramic contact (TiO₂/WC) thus reducing the friction and improving the wear resistance of the materials. Furthermore, the ionic character of the oxide layer improved its wettability compared with that of titanium’s surface, therefore creating a desired boundary lubricating effect [24]. The CoF became more unsteady after 400 cycles which might be because some of the oxide layers were peeled off (inset picture in Fig. 10b) and the hard ceramic debris led to a more fluctuated friction. However, the wear area and wear rate were much less than that of the untreated CP-Ti (Table 2).

The gold pre-deposited CP-Ti samples all had lower and more stable friction although they increased with the testing time. It was reported that gold in sputtering-produced TiO₂ layer can reduce the CoF to 0.16–0.23 against bearing steel in a reciprocating tribotest [28]. Gold particles could self-restore under the applied load because of their low shear strength even if a local failure occurred in the TiO₂ layer, therefore reducing the friction and increasing the wear resistance in a sliding test [29]. However, it was found the track on the samples Au9m620/40 and Au9m620/80 were wider and deeper, and part of the oxide layers was peeled off in the wear track, this might be due to they having a thick oxide layer (> 3.5 µm). With the increase in thickness, there are more defects in the oxide layer which could result in the spallation under a load in the scratch and tribotest. For sample Au9m620/3 and sample Au9m660/3, the wear tracks were shallower and smoother, and the wear rate was lower and similar to that of sample 620/80, which could be attributed to a slightly thinner oxide layer (1.8–2.7 µm) with fewer defects. With the help of gold, a 3-hour short-time treatment can obtain an oxide layer with similar tribological properties to that of the 80-hour treatment without any gold, and thus greatly increase the efficiency of ceramic conversion treatment.

In this research, a thin gold layer with different thicknesses was used to accelerate the ceramic conversion treatment of commercially pure titanium alloy. A smaller amount (∼15 nm) of the pre-deposited gold layer can accelerate the CCT of the CP-Ti alloy by increasing the thickness of the oxide layer, especially in the initial stages of the treatment (3 hours), at temperatures of 620°C and 660°C. With more gold (∼30 nm) on the surface, the effect became more significant; however, when further increasing the amount of gold layer to 45 nm, the oxide layer increased only slightly in comparison to those CCTed at the same condition with less gold.

The gold-rich zone at the interface of the oxide layer and the matrix proves that the gold can promote the outward diffusion of titanium through the gold layer. Gold nanoparticles and clusters were also found in the surface region and the oxide layer after CCT. The surfaces were generally smoother and harder for the samples with a pre-deposited gold layer. They had low and stable friction and very small wear volume thanks to the lubrication of embedded gold nanoparticles and clusters in the compact titanium dioxide layer. However, the gold particle in the oxide layer has a limited effect to improve the adhesion and cohesion of the oxide layer in the scratch test.

With the assistance of pre-deposited gold thin layer, the efficiency of the ceramic conversion treatment increased significantly. The ceramic oxide layer formed after a 3-hour treatment (Au9m620/3, Au9m660/3) can achieve a similar tribological performance to the typical treatment of 80-hour (620/80).

Conflicts of Interest Statement

The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Pałka, K.; Pokrowiecki, R. Porous Titanium Implants: A Review. Adv. Eng. Mater. 2018, 20, 1700648. DOI:10.1002/adem.201700648.
Karabakhin, V.G.; Zor'kina, N.A. Antifriction surfacing of titanium alloys. Weld. Int. 2012, 26, 409–410. DOI:10.1080/09507116.2011.600086.
Li, X.; Dong, H. 14 - Ceramic conversion treatment of titanium-based materials. In Surface Engineering of Light Alloys, Woodhead Publishing: 2010; pp 475–500. DOI:10.1533/9781845699451.2.475.
Jia, D.; Zhang, Y.; Li, C.; Yang, M.; Gao, T.; Said, Z.; Sharma, S. Lubrication-enhanced mechanisms of titanium alloy grinding using lecithin biolubricant. Tribol. Int. 2022, 169, 107461. DOI:10.1016/j.triboint.2022.107461.
Ben Aissa, C.; Khlifi, K. CAE-PVD synthesis and characterization of titanium-based biocompatible coatings deposited on titanium alloy for biomedical application. Mater. Today. 2021, 42, A10-A17, DOI:10.1016/j.matpr.2021.04.247.
Malhotra, R.; Han, Y.; Nijhuis, C.A.; Silikas, N.; Castro Neto, A.H.; Rosa, V. Graphene nanocoating provides superb long-lasting corrosion protection to titanium alloy. Dent. Mater. 2021, 37, 1553–1560, DOI:10.1016/j.dental.2021.08.004.
Rie, K.T.; Lampe, T.; Eisenberg, S. Plasma Heat Treatment of Titanium and Titanium Alloy Ti-6Al-4V: Effect of Gas Composition and Temperature. Surf. Eng. 1985, 1, 198–202. DOI:10.1179/sur.1985.1.3.198.
Zhu, Y.S.; Wei, X.N.; Yin, Y.X. A novel low temperature and green salt bath nitriding of titanium alloy. Surf. Eng. 2021, 37, 1422–1431. DOI:10.1080/02670844.2021.1979841.
Atmani, D.; Saoula, N.; Abdi, A.; Azzaz, M.; Wang, Y.; Mohamedi, M. Structural, Morphological, and Electrochemical Corrosion Properties of TiO₂ Formed on Ti6Al4V Alloys by Anodization. Cryst. Res. Technol. 2018, 53, 1800138. DOI:10.1002/crat.201800138.
Dong, H.; Bloyce, A.; Morton, P.M.; Bell, T. Methods of case hardening of titanium alloys. EU: EP1000180, 2001.
Guleryuz, H.; Cimenoglu, H. Surface modification of a Ti6Al4V alloy by thermal oxidation. Surf. Coat. Technol. 2005, 192, 164–170. DOI:10.1016/j.surfcoat.2004.05.018.
Zhang, Z.; Zhang, Y.; Li, X.; Alexander, J.; Dong, H. An enhanced ceramic conversion treatment of Ti6Al4V alloy surface by a pre-deposited thin gold layer. J. Alloys Compd. 2020, 844, 155867, DOI:10.1016/j.jallcom.2020.155867.
Zhang, Z.X.; Dong, H.; Bell, T. Role of gold in high temperature oxidation of titanium alloy. Surf. Eng. 2005, 21, 76–79. DOI:10.1179/174329405X30048
Zhang, Z.X.; Dong, H.; Bell, T.; Xu, B.S. The Effect of Gold Pre-Deposition on the Oxidation Behavior of CPTi and Ti6Al4V Alloy. Oxid. Met. 2006, 66, 91–106.DOI: 10.1007/s11085-006-9026-x.
Antler, M.; Spalvins, T. Lubrication with thin gold films. Gold Bull. 1988, 21, 59–68. DOI:10.1007/bf03214666.
Hussain, M.; Ahmad, M.; Nisar, A.; Sun, H.; Karim, S.; Khan, M.; Khan, S.D.; Iqbal, M.; Hussain, S.Z. Enhanced photocatalytic and electrochemical properties of Au nanoparticles supported TiO₂ microspheres. NJC 2014, 38, 1424–1432. DOI:10.1039/c3nj01525d.
Chen, Y.; Tang, Y.; Luo, S.; Liu, C.; Li, Y. TiO2 nanotube arrays co-loaded with Au nanoparticles and reduced graphene oxide: Facile synthesis and promising photocatalytic application. J. Alloys Compd. 2013, 578, 242–248. DOI:10.1016/j.jallcom.2013.04.180.
Armelao, L.; Barreca, D.; Bottaro, G.; Gasparotto, A.; Maccato, C.; Maragno, C.; Tondello, E.; Štangar, U.L.; Bergant, M.; Mahne, D. Photocatalytic and antibacterial activity of TiO2and Au/TiO₂ nanosystems. Nanotechnology 2007, 18, 375709. DOI:10.1088/0957-4484/18/37/375709.
Fernandes, F.; Morgiel, J.; Polcar, T.; Cavaleiro, A. Oxidation and diffusion processes during annealing of TiSi(V)N films. Surf. Coat. Technol. 2015, 275, 120–126. DOI:10.1016/j.surfcoat.2015.05.031.
Hutchings, G.J. Selective oxidation using supported gold bimetallic and trimetallic nanoparticles. Catal. Today 2014, 238, 69–73. DOI:10.1016/j.cattod.2014.01.033.
Chen, M.S.; Goodman, D.W. The Structure of Catalytically Active Gold on Titania. Science 2004, 306, 252–255. DOI:10.1126/science.1102420.
Wu, M.; Moulin, J.; Coste, P.; Perrot, S.; Perrossier, J.L.; Renard, C.; Bosseboeuf, A. Comparative study of Au/Ti, Au/V and Au/Zr films oxygen gettering ability. Thin Solid Films 2016, 616, 543–549. DOI:10.1016/j.tsf.2016.09.003.
Busiakiewicz, A.; Kisielewska, A.; Piwoński, I.; Batory, D.; Pabianek, K. Formation of gold and platinum nanostructures on rutile TiO₂(001) by thermal treatment of thin films in vacuum. Vacuum 2019, 163, 248–254, DOI:10.1016/j.vacuum.2019.02.026.
Dong, H.; Bell, T. Enhanced wear resistance of titanium surfaces by a new thermal oxidation treatment. Wear 2000, 238, 131–137. DOI:10.1016/S0043-1648(99)00359-2.
Yoshihara, M.; Miura, K. Effects of Nb addition on oxidation behavior of TiAl. Intermetallics 1995, 3, 357–363, DOI:10.1016/0966-9795(95)94254-C.
Debeila, M.A.; Raphulu, M.C.; Mokoena, E.; Avalos, M.; Petranovskii, V.; Coville, N.J.; Scurrell, M.S. The effect of gold on the phase transitions of titania. Mater. Sci. Eng.: A 2005, 396, 61–69. DOI:10.1016/j.msea.2004.12.047.
Fellah, M.; Labaïz, M.; Assala, O.; Dekhil, L.; Taleb, A.; Rezag, H.; Iost, A. Tribological behavior of Ti-6Al-4V and Ti-6Al-7Nb Alloys for Total Hip Prosthesis. Adv. Tribol. 2014, 1–13., DOI:10.1155/2014/451387.
Abreu, C.S.; Matos, J.; Cavaleiro, A.; Alves, E.; Barradas, N.P.; Vaz, F.; Torrell, M.; Gomes, J.R. Tribological characterization of TiO₂/Au decorative thin films obtained by PVD magnetron sputtering technology. Wear 2015, 330–331, 419–428. DOI:10.1016/j.wear.2015.01.069.
Liu, W.-m.; Chen, Y.-x.; Kou, G.-T.; Xu, T.; Sun, D.C. Characterization and mechanical/tribological properties of nano Au–TiO₂ composite thin films prepared by a sol–gel process. Wear 2003, 254, 994–1000, DOI:10.1016/S0043-1648(03)00305-3.

No competing interests reported.

Download PDF

Journal Publication

published 25 Feb, 2023

Read the published version in Tribology Letters →

Editorial decision: Major revision
22 Dec, 2022
Reviews received at journal
15 Dec, 2022
Reviewers agreed at journal
06 Dec, 2022
Reviewers invited by journal
06 Dec, 2022
Editor assigned by journal
30 Nov, 2022
Submission checks completed at journal
30 Nov, 2022
First submitted to journal
30 Nov, 2022

You are reading this latest preprint version

Impact of the amount of the gold layer on the tribological performance of the ceramic conversion treated CP-Titanium

Status:

Journal Publication

Version 1

Abstract

Figures

1: Introduction

2: Experimental

3: Results

3.1: Surface morphology and roughness change

3.2: Thickness of the oxide

3.3: Surface phase constituents

3.4: Mechanical properties

3.4.1 Surface Microhardness

3.4.2 Cross sectional nanohardness profiles

3.4.3 Scratch testing on the converted ceramic oxide layers

3.4.4 Reciprocal friction and wear test against WC ball

4: Discussion

5: Conclusions

Declarations

References

Additional Declarations

Status:

Journal Publication

Version 1