[1] Wang X, Bi Q, Zhu L, Ding H. Improved forecasting compensatory control to guarantee the remaining wall thickness for pocket milling of a large thin-walled part. Int J Adv Manuf Technol 2016; 94(5-8):1677-88.
[2] Schmitt RH, Peterek M, Morse E, et al. Advances in Large-Scale Metrology – Review and future trends. CIRP Ann-Manuf 2016; 65(2):643-65.
[3] Zhang J, Lin B, Fei J, et al. Modeling and experimental validation for surface error caused by axial cutting force in end-milling process. Int J Adv Manuf Technol 2018; 99(1):327-35.
[4] Gonzalo O, Seara JM, Olabarrieta E, et al. Case Study 1.2: Turning of Low Pressure Turbine Casing. Intelligent Fixtures for the Manufacturing of Low Rigidity Components: Springer, 2018;25-38.
[5] Fu Q, Lorite GS, Rashid MM-U, et al. Suppressing tool chatter with novel multi-layered nanostructures of carbon based composite coatings. J Mater Process Technol 2015; 223:292-8.
[6] Kolluru K, Axinte D. Novel ancillary device for minimising machining vibrations in thin wall assemblies. Int J Mach Tools Manuf 2014; 85(7):79-86.
[7] Kolluru K, Axinte D, Becker A. A solution for minimising vibrations in milling of thin walled casings by applying dampers to workpiece surface. CIRP Ann-Manuf 2013; 62(1):415-8.
[8] https://www.mtorres.es/sites/default/files/documentos/fichas-de-producto/Torresmil%26Torrestool_0. pdf.
[9] Qin G, Zhang W, Wan M. Analysis and optimal design of fixture clamping sequence. J Manuf Sci Eng 2005; 128(2):482-93.
[10] Chaari R, Abennadher M, Louati J, Haddar M. Mathematical methodology for optimization of the clamping forces accounting for workpiece vibratory behaviour. Int J Simul Multidiscipl Des Optim 2014; 5:A13.
[11] Chen W, Ni L, Xue J. Deformation control through fixture layout design and clamping force optimization. Int J Adv Manuf Technol 2007; 38(9):860-7.
[12] Sundararaman KA, Padmanaban KP, Sabareeswaran M. Optimization of machining fixture layout using integrated response surface methodology and evolutionary techniques. Proc Inst Mech Eng Part C-j Eng Mech 2015; 230(13):2245-59.
[13] Yang B, Wang Z, Yang Y, Kang Y, Li X. Optimum fixture locating layout for sheet metal part by integrating kriging with cuckoo search algorithm. Int J Adv Manuf Technol 2016; 91(1-4):327-40.
[14] Liu SG, Zheng L, Zhang ZH, Li ZZ, Liu DC. Optimization of the number and positions of fixture locators in the peripheral milling of a low-rigidity workpiece. Int J Adv Manuf Technol 2007; 33(7-8):668-76.
[15] Zeng S, Wan X, Li W, Yin Z, Xiong Y. A novel approach to fixture design on suppressing machining vibration of flexible workpiece. Int J Mach Tools Manuf 2012; 58:29-43.
[16] Balachandran B. Nonlinear dynamics of milling processes. Philos T Roy Soc A 2001; 359(1781):793-819.
[17] Long X. Loss of contact and time delay dynamics of milling processes. Doctoral dissertation, University of Maryland, 2006.
[18] Shamoto E, Mori T, Nishimura K, Hiramatsu T, Kurata Y. Suppression of regenerative chatter vibration in simultaneous double-sided milling of flexible plates by speed difference. CIRP Ann-Manuf 2010; 59(1):387-90.
[19] Mori T, Hiramatsu T, Shamoto E. Simultaneous double-sided milling of flexible plates with high accuracy and high efficiency—Suppression of forced chatter vibration with synchronized single-tooth cutters. Precis Eng 2011; 35(3):416-23.
[20] Fei J, Lin B, Xiao J, et al. Investigation of moving fixture on deformation suppression during milling process of thin-walled structures. J Manuf Processes 2018; 32:403-11.
[21] Fei J, Lin B, Yan S, et al. Chatter mitigation using moving damper. J Sound Vib 2017; 410:49-63.
[22] Ozturk E, Barrios A, Sun C, Rajabi S, Munoa J. Robotic assisted milling for increased productivity. CIRP Annals 2018; 67(1):427-30.
[23] Huang T, Dong C, Liu H, Sun T, Chetwynd DG. A simple and visually orientated approach for type synthesis of overconstrained 1T2R parallel mechanisms. Robotica 2018:1-13.
[24] Huang T, Chenglin D, Liu H, et al. Five-degree-of-freedom hybrid robot with rotational supports, US Pantent, US9943967B2, 2018.
[25] Dong C, Liu H, Yue W, Huang T. Stiffness modeling and analysis of a novel 5-DOF hybrid robot. Mech Mach Theory 2018; 125:80-93.
[26] Xiao J, Xu F, Zhao S, Huang T, B L. An integrated pneumatic rigid mirror milling flexible support device for real-time measurement of thickness, China Patents, 2017.
[27] Liu Q, Huang T. Inverse kinematics of a 5-axis hybrid robot with non-singular tool path generation. Robot Cim-int Manuf 2019; 56:140-8.
[28] Liu Q, Xiao J, Yang X, Liu H, Huang T, Chetwynd DG. An iterative tuning approach for feedforward control of parallel manipulators by considering joint couplings. Mech Mach Theory 2019; 140:159-69.